Updates & Feature Releases 🚀
Take action on a miner from the Miner Details page
You can now act on a miner directly from its Miner Details page. A new actions menu sits in the page header, right next to Edit Miner.
Until now, the only place to send a command to a miner was its row in the miner table. If you were on the Miner Details page looking at a miner’s charts, activity, or logs and spotted a problem, you had to leave the page, go back to the miner table, search or filter to find that same miner again, and then run the action from its row. That broke your train of thought and cost time, especially at large sites. Now you can go from diagnosing a miner to fixing it without leaving the page.
- Actions run from this menu work exactly the same as when you run them from the miner table, so there is nothing new to learn.
- Each command you send appears in the Pickaxe Command History section on the same page right away, with no refresh needed.
- The status of your most recent command, including a failure, stays visible at a glance without scrolling or reopening the menu, so you know right away whether the reboot went through.
Per-outlet control for DoyonTek IPDUv3 PDUs
Sites running DoyonTek IPDUv3 smart PDUs can now turn individual outlets on or off, or reboot them, directly from Foreman. This lets operators hard-reboot a stuck miner or cut load at the outlet without logging into each PDU’s own web interface. Foreman already showed PDU and per-outlet power readings for these units. This release adds control on top of that monitoring.
- After each command, Foreman reads the outlet’s state back to confirm the result.
- Outlets on cascaded DoyonTek units are supported.
DigitalShovel smart PDUs now place miners on your site map automatically
DigitalShovel smart PDUs know which miner is plugged into each outlet. Foreman now reads that through Pickaxe and places each miner at the site map location assigned to its PDU port. When a miner moves to a different outlet, Foreman updates its location for you, so sites that move and swap miners often no longer have to keep the site map current by hand. Because Foreman already uses each port’s measured power for the miner plugged into it, that power reading now follows the right miner as it moves.
- To get started, add your DigitalShovel PDUs on the Infrastructure page and associate each port with its site map location.
- DigitalShovel identifies miners by IP address, so keep miner IPs accurate in Foreman.
Fixes & Improvements 🛠️
Inline table edits now stay put after saving
- When you edited a cell directly in a table, such as on the Tickets or Offline Locations pages, the save went through, but the cell could briefly jump back to its old value until you refreshed the page. Edited cells now keep the saved value right away.
Tickets Owners filter includes former team members
- On the Tickets page, the Owners filter now lists everyone who owns tickets, including people who are no longer on your team. Their tickets were always kept, and their names still appeared in the Owners column, but you could not filter by them. You can now pull up every ticket a former team member owned in one step.
Bulk ticket deletes now appear in ticket history
- Deleting several tickets at once now records a delete entry in each ticket’s history, showing who deleted it and when, the same way single-ticket deletes always have. This matters for teams that rely on tickets for asset tracking and invoicing records. Bulk deletes made before this fix did not record history, and those entries cannot be recovered.
Audit log details and Action filter
- The Action filter now includes Change Client Owner, Restart Miners, Fan Mode, Advanced Thermal Management, and No PIC Protection Mode. These events already appeared in the log, and you can now filter for them.
Pickaxe miner type detection keeps usernames and passwords in sync
- When a miner is set up in Foreman as running Vnish or another third-party firmware, and Pickaxe detects that it is now running something different, such as stock firmware, Pickaxe switches the miner to the new firmware’s default login. Until now, it changed only the password and kept the old username, so the login no longer matched. The miner could get stuck, with commands failing and stats not coming in until someone fixed it by hand. Pickaxe now updates the username and password together when it detects a firmware change, so commands and stats keep working.
API reliability and documentation cleanup
- Customers using the Foreman API will see clearer responses in a few cases that previously returned a server error. Checking report results with an invalid report key now returns the standard “not allowed” response, and sending an unsupported request to a single Pickaxe’s address now returns “method not allowed”. The published API reference also no longer lists data definitions for retired metrics endpoints, so the documentation matches what the API returns.